Can Command Hooks Hold Blackout Curtains? Weight Limits, Setup and Alternatives


Soft white pillows on a bed with morning light, representing the need for darkness tools like sleep masks or blackout curtains

Command hooks can hold blackout curtains, but only if the rod and panels together stay under the hook’s rating, the rod fits the hook, and the wall is clean and dry. Heavy lined panels, wide windows and fresh or textured paint are where they most often fail. Here is what the packs actually say, how to install them properly, and what to use if your curtains are too heavy.

This is a companion to our complete guide to no-drill blackout curtains, which compares every method.

What the packs say

Command curtain rod hooks come in more than one rating, and the details on the pack matter more than the brand name. These are the figures we found on retailer and 3M listings. Packs change, so check the one you buy.

PackWeight ratingRod notes on the listing
Standard curtain rod hooks (2 hooks, 4 strips)5 lbRod under 5/8 inch across and under 48 inches long
Large, matte black curtain rod hooks (2 hooks, 4 strips)10 lbRods about 0.5 to 0.75 inch across

Two details are easy to miss. First, the 5 lb listing we checked states that using more than one hook for an item leaves the total capacity at one hook’s rating, so adding extra hooks does not multiply the limit. Second, the rod length cap on that pack means a wide window may be out of range for that product altogether.

Will they hold your curtains? Weigh first

The rating applies to the rod plus the curtains hanging on it. Weigh both together: step on a bathroom scale on your own, then holding the rod and panels, and subtract. Then compare.

  • Well under the rating: a reasonable fit. Leave a safety margin, not a near miss.
  • Close to the rating: go up a size or choose a different method.
  • Over the rating: do not use adhesive hooks. Coated, thermal-lined and velvet blackout panels often land here, and several renter guides name weight as the most common cause of failure.

Reviews of Command curtain rod hooks are mixed. Some people report them holding for years, while others report hooks coming down within hours or weeks with heavier or multiple curtains. That spread fits the pattern: the same hook works with light panels and a clean wall, and fails when the load, the surface or the prep is wrong.

How to install them so they stay up

Follow the instructions on your pack. The steps printed on Command packs are consistent, and the details below match them.

  1. Mark the spots. Place the hooks so the rod sits 4 to 6 inches above the window frame and extends past each side, and use a level so the rod will not tilt.
  2. Clean with rubbing alcohol. The packs say to use rubbing alcohol and not household cleaners or water, which can leave a slippery residue. Let it dry.
  3. Apply the strips and hooks as shown on the pack, making sure the pull tab stays accessible for removal.
  4. Press firmly for 30 seconds.
  5. Wait one hour before hanging anything, so the adhesive reaches full strength.
  6. Hang the rod, then the curtains. Slide the panels along the rod. Do not pull them down.
  7. Check after a week. If a hook has shifted, take it down before it fails.

Command’s adhesive is rated for indoor use within a temperature range. The pack we saw lists roughly 50 to 105°F, so a wall that bakes in direct sun or sits in a damp corner is a weak spot.

Why Command hooks fail with blackout curtains

  • Overloaded rod. Heavy lined panels plus a metal rod add up fast.
  • Wrong rod size. A rod too thick for the hook sits badly and puts uneven strain on the adhesive.
  • Dirty, damp or textured wall. Wall condition affects adhesion more than most guides admit. Fresh paint and heavy texture are the usual culprits, so test a hidden spot first.
  • Skipping the wait. Hanging the rod before the hour is up weakens the bond.
  • Pulling the curtains. Yanking them across the rod loads the hooks sideways and down.
  • Heat and humidity. A sun-baked or steamy wall can soften the adhesive.

Taking them down without damage

Take the curtains and rod down first. Hold the hook gently in place, then pull the strip tab slowly straight down along the wall. The packs say never to pull the strip toward you, and they give a minimum stretch distance, such as at least 6 inches for small hooks and at least 15 inches for large ones. Do not twist the hook. Any residue usually rubs off with rubbing alcohol on a cloth.

What to use if your curtains are too heavy

  • Lighter panels or a lighter rod. Sometimes the simplest change is swapping to a thinner, lighter blackout panel.
  • Tap-in frame brackets on a wood frame, if your lease allows tiny pin marks.
  • Stick-on blackout shades or hook-and-loop panels that do not use a rod at all.
  • Magnetic rods only for light panels on steel doors or frames.

Our no-drill blackout curtains guide compares all seven methods side by side. Whichever you pick, seal the edges: see how to stop light leaking around blackout curtains.

FAQ

Can you hang a curtain rod with Command hooks?

Yes, with hooks made for curtain rods, as long as the rod fits the hook and the total weight stays under the rating.

How much weight can Command curtain rod hooks hold?

The packs we found were rated at 5 lb and 10 lb. Check the rating on the exact pack you buy, and remember the limit covers the rod and curtains together.

Do more hooks mean more weight capacity?

Not on the listings we checked. The 5 lb pack states that using more than one hook for an item leaves the total capacity at one hook’s rating.

How long do you wait before hanging curtains?

One hour after pressing the hooks to the wall, according to the instructions printed on Command packs.

Will Command hooks damage my walls?

They are designed to remove cleanly if you pull the strip straight down, slowly. Damage usually comes from overloading them, fresh paint that has not bonded, or pulling the strip toward you.

The bottom line

Command hooks are a good fit for a light rod with lightweight blackout panels on a clean, dry wall, and a poor fit for heavy lined panels or wide windows. Weigh before you buy, follow the pack steps exactly and keep a safety margin. If the numbers do not work, choose a different method rather than hoping the adhesive wins.

This article is for general information. Always follow the manufacturer’s instructions and weight ratings on your product. Last updated October 28, 2026.

Sources

Leo

Leo runs SleepWellSpace — free sleep tools and practical guides. Not a doctor. Writes clearly, cites sources, and labels what was and was not personally tested.

Recent Posts